“No Atomizer” means your Yocan battery cannot detect a cartridge on its 510 connection, so it refuses to fire. “Shorted” means it found a connection, but the circuit reads as a short or the coil resistance is too low. Clean and reseat first, then swap cartridges to find out which part is at fault.
Quick fix table
| What you see | What it means | Try this first |
|---|---|---|
| “No Atomizer” or a no-cartridge message | No load detected across the 510 contacts | Turn off, remove the cartridge, wipe both contacts, reconnect gently snug |
| “Shorted” or a short-circuit warning | Short circuit, or coil resistance below the supported minimum | Remove the cartridge at once, dry the contacts, test a known-good cartridge |
| Kodo Star: resistance reading and Ω flash 3 times | No load (no cartridge detected) | Same as No Atomizer |
| Kodo Star: voltage and V flash 3 times | Short circuit | Same as Shorted |
| Lights flash but there is no screen | A model-specific blink code | Match the pattern in the blink-code guide |
Both messages are protection features. They stop the battery from firing into a connection it cannot read safely, so the fix is usually at the connection or the cartridge rather than inside the battery.
What “No Atomizer” means
No Atomizer means the battery sees nothing connected across its contacts. Yocan's Kodo Star manual calls this a “no load” condition. The cartridge may be fine; the battery simply is not reaching its coil.
Yocan's help centre points to the same causes for the Kodo Pro, and they apply to most 510 batteries:
- A loose connection between the cartridge and the battery.
- Dirty or sticky contact surfaces.
- A faulty cartridge.
- A battery that is too low to work properly.
On adapter-based batteries such as the UNI series and Ziva Pro, a missing, dirty or poorly seated magnetic adapter is another common cause.
What “Shorted” means
Shorted means the battery measured a short circuit or a resistance below its safe minimum and cut power. Yocan's Kodo Pro manual defines the message as a short circuit or an atomizer resistance under 0.8 ohms, and the Kodo Star stops output under the same conditions.
Typical causes are liquid or residue bridging the contacts, a cartridge centre post pushed in by overtightening, a damaged cartridge, or an attachment rated below the battery's supported resistance. Yocan notes that a wax atomizer fitted to a Kodo Pro may trigger the short warning for exactly this reason. Remove the cartridge as soon as the message appears and do not keep pressing the button to see whether it clears.
A fix order that works on any Yocan 510 battery
Work through these steps in order and change one thing at a time.
- Turn the battery off and remove the cartridge. On most buttoned Yocan batteries that is five quick presses of the power button.
- Check the charge. A very low battery can produce connection errors on some models. If the battery indicator is low, charge it first; the not-charging checklist covers cable and port problems.
- Inspect both parts. Look for leakage, cracks, a centre post that sits crooked or sunk, and, on UNI or Ziva models, a missing or loose magnetic adapter.
- Clean the contacts. Start with a dry cotton swab. Yocan's cleaning guidance allows a swab lightly dampened with isopropyl alcohol on the connection points. Let everything dry completely before reconnecting.
- Reconnect gently. Thread the cartridge or adapter until it is just snug, then stop. Overtightening can push the centre contact down and either break the connection or create a short.
- Swap to isolate the fault. Try a known-good cartridge on this battery, and the suspect cartridge on another compatible battery if it is clean and undamaged.
- Check resistance. Several current Yocan batteries, including the Kodo Pro, Kodo Star, LUX 2.0 and Ziva Pro, list support for coils above 0.8 ohms. A lower-resistance attachment will trigger the short warning.
The swap test usually gives a clear answer:
- A known-good cartridge works: the original cartridge is the problem. Cartridges are consumables and are not covered by the battery's warranty.
- The suspect cartridge fails on two batteries: discontinue that cartridge.
- Every known-good cartridge fails on one battery: the battery needs a warranty assessment.
Model-specific notes
These notes add what is different about each model. Setup and voltage instructions stay in the full manuals linked below.
Kodo Pro
The Kodo Pro reports both errors as text on its OLED screen. Its manual's display table explains the no-cartridge warning as “No atomizer connected” and SHORTED as a short circuit or atomizer resistance under 0.8 ohms. The manual also says the screen shows the cartridge's resistance once it is connected, which makes a useful check: if a resistance value appears after you thread the cartridge on, the battery is reading the connection. Full setup is in the Kodo Pro manual.
Kodo Star
The Kodo Star has no text messages; it flashes parts of its Galaxy display instead. Per Yocan's manual, the resistance reading and Ω flash three times when no cartridge is connected, and the voltage and V flash three times when it detects a short. A full-screen flash of five times is the 15-second safety cutoff, not a connection fault. The Kodo Star manual explains the whole display.
UNI Pro
Most UNI Pro connection errors come from the magnetic adapter. Confirm it is threaded onto the cartridge, clean the adapter and chamber contacts, and set the height so the adapter sits flat. For a shorted message, Yocan's help centre gives two fixes for UNI-series flash errors: switch the cartridge or loosen the adapter. An adapter screwed down hard can push the cartridge's centre post in. Step-by-step adapter fitting is in the UNI Pro manual.
UNI 3.0
The UNI 3.0 uses the same magnetic-adapter idea. Yocan's UNI 3.0 FAQ answers its short-circuit error with three checks: make sure the cartridge is properly connected to the magnetic ring, do not overtighten it or leave it too loose, and clean the connection points with a cotton swab dipped in alcohol. The adapter steps in the UNI Pro manual apply here as well.
LUX 2.0
The LUX 2.0 is a pen-style battery that threads directly onto the cartridge. Yocan's LUX 2.0 page says its OLED screen can show the resistance value, and that it supports coils above 0.8 ohms. Read the message on the screen, then follow the general fix order; for the exact wording on your unit, use the leaflet supplied with it.
Ziva Pro
The Ziva Pro shows “NO ATOMIZER” on its screen when it detects no cartridge. Yocan's Ziva Pro FAQ says to check the connection, clean any debris from the connection port, and confirm the cartridge is above 0.8 ohms. The cartridge sits inside the body on its adapter, so make sure the adapter is threaded on and the cartridge is seated straight. A locked screen is a separate feature, not an error; unlock it using the sequence in the manual supplied with your unit.
Ari 2.0 and Flat 2.0
The Ari 2.0 Plus sets voltage with a twist dial and is listed for cartridges of 0.8 ohms or more. The Flat 2.0 Plus has an OLED screen with a puff counter. We could not confirm a published, model-specific error list for either, so read any message or light pattern against the leaflet in your box and the blink-code guide. The general fix order above applies to both.
When to stop and get warranty support
Stop using the battery straight away if it is hot, swollen or cracked, or smells unusual, and do not reconnect it to a charger. Do not pry, bend or lift any contact with a knife, pin, pliers or paperclip, and do not open the battery or try to bypass its protection. Those steps can turn a cartridge fault into a battery fault.
If several known-good cartridges produce the same error on one battery, it needs a warranty assessment. Yocan's standard quality guarantee for qualifying devices is three months from purchase, and Yocan routes claims through the seller first. Read our warranty policy, then contact our support team with the model, the exact message or flash pattern, the cartridges you tested and a short video.
Official references
Common questions
What does No Atomizer mean on a Yocan battery?
The battery cannot detect a cartridge across its 510 contacts, so it will not fire. The usual causes are a loose or dirty connection, a missing magnetic adapter, a low battery, or a faulty cartridge.
What does Shorted mean on a Yocan battery?
The battery has detected a short circuit or a coil resistance below what it supports, and it has cut power to protect itself. On current Kodo models that limit is 0.8 ohms.
Is No Atomizer a battery problem or a cartridge problem?
Usually the cartridge or the connection. Clean and reseat it, then try a known-good cartridge. If several good cartridges fail on the same battery, the battery needs a warranty assessment.
Can I fix a Yocan short by lifting the centre pin?
No. Do not pry or bend any contact with metal tools. The centre contact is insulated from the thread, and damaging that insulation can create a real short. Clean, reseat and swap parts instead.
Why does my Kodo Star flash Ω instead of saying No Atomizer?
The Kodo Star has no text messages. Yocan's manual says the resistance reading and the Ω symbol flash three times when no cartridge is connected, which is its version of a No Atomizer warning.

